- Stop in and set a spell.
- problem
- The vibration continues
- Overflow tank update..
- Attn: Carb Guys!
- Popping at higher RPMs (from old board)
- Unsure of route to travel opinions wanted
- ARP head stud question
- Heads/machining cost questions
- Inj & MAF ?
- How does a EFI motor run lean??
- Pulling motor questions
- Valve job questions
- Starter wiring question
- Drilling throttle body?
- Got my heads back yesterday
- Heads...torqueing, etc.
- Head Gasket
- valve lash
- Did I hurt something?
- Frustration at it's MAX!!
- o2 sensors maybe?
- Another valve question.
- Equal length VS. Unequal
- More rocker arm Q & A
- Horsepower Vs. Torque
- Looking for advice on which fuel pressure regulator to buy.
- HCI help
- Rear Main seal?
- Rack and pinon help
- fun with EFI
- My car....frustrating
- fuel management unit
- Check Engine Light on a 92
- turn signals?
- Ticking noise under the hood...
- Ticking part II
- Help, driveshaft isn't budging
- What to do?
- I need some advice...what would you guys do?
- MAF Screen
- Holley Heads
- Headers
- Tensioner?
- Cam, intake, inj. match?
- fan controller
- Spout out?
- Poly locks and rocker arms
- In my quest for strange and obscure engine parts...
- New Combo, am I missing anything?
- Alternator pulley question.
- loss of power
- Which Pump?
- Fan install tomorrow
- Well at least it didn't burn to the ground
- AFPR or not?
- Thanks to all!
- Charging problem
- Stock valve cover mod?
- Does 2 quarts sound right for 8.8 fluid change?
- solid cam question?
- Proper Cam for rebuild?
- Stroker tech
- BTM help
- Where do I Find
- Fuel filter
- anyone need some 5.4" rods
- Totally confused, WTF!?!
- What is the h.p. limit...
- O-rings for injectors
- speed density(sp)
- Any 408 stangs out there?
- Lifter problem driving me f-ing crazy!!!
- More Problems....
- Looking for machine shop recommendations.
- Need suggestions for carbed cam.
- Part # for A/C Eliminator?
- Changing out camshaft?
- Has anyone run a 351w in a 64 to 66??
- Fuel Injectors???
- wont idle or stay running
- What year....
- I need a wiring diagram please
- Summit Long tubes
- Shift light question
- what year 5.0 from 86-93...
- head delema
- How much HP thru a stock 351 block
- mass air sensor?
- head bolt torque
- electric fan question
- 351 in a fox
- engine vibration
- Motor Pull question
- Crank Suggestions
- 12:50-12:90's
- supercharge a speed density?
- What size injector?
- SFI Balancer
- Timing Chain
- I think I found the screw...........pics
- AFR 185's
- Who has the cheapest 331 kit??
- Rod
- Shorty Headers????
- HP estimates?
- KB pistons
- Dumps vs. Tailpipes
- Need intake spacer bolt help
- Cam size?
- Dyno numbers are in.....................
- synthetic oil service life
- Cam question
- deck height
- another cam question
- Couple of questions on the valve train
- Firing Order
- bad rings
- question on chip
- intake swap
- Gauge Question
- How are the GT-40X Turbo Swirl Heads?
- Machine shops - Where is your favorite?
- 130amp alternator conversion
- anyone have this happen before?
- Fulidyne is in...question
- speedo broke
- running too rich?
- Air/Fuel Gauge
- help
- 302 to 35W flywheel/bellhousing
- need some opinions
- Help ASAP Valve Cover issue.
- Idle RPM
- starter problem!
- Tune-up...
- Headers
- Headers for BBF in 67 stang
- push rod length for B cam and 1.7 rockers
- Plug wires
- 1 step forward 5 steps back.......
- need help
- Car won't idle.....help
- lower trickflow gasket
- electric fuel pump question
- Strange problem..??
- idle problems on my 95 stang
- cam question
- Vacuum leak or pcv hooked up wrong??
- bad coil diagnosis
- fuel line fitting....
- Freeze Plug help
- Cant get the camshaft out
- Stuttering at WOT
- t 5 swap flywheel ?
- Weird issues....
- A3M1 computer in my fox?
- For anyone running sheet metal/aluminum valve covers.
- anyone know stock cam #'s ?
- Any tests to check a mass air meter...
- foxbody underdrive pulleys
- benefits of advanced timing
- Strange 9 inch housing ends
- 351w swap
- HP Limit on 19# injectors?
- help ordering header gaskets
- head swap (289 hi-po from e7te)
- Belt Question?
- evaperation canister????
- trick flow head identification?
- Will 5.0 pass emissions?
- clutch installation question
- need a little advice
- 88 T-bird header ?
- Spark plug wires
- Firing order on 289 heads?
- flowtech headers
- 351 Blocks
- Tuners?
- blown motor
- Found my vacuum leak!!!!!!!!
- how much will it cost?
- A/F tuner...
- Belt shredding issues
- Tuning gains
- Need some lifter advice/help
- 351w shipping weight?
- 351w shortblock weight
- smell antifreeze dont see any leak!!???
- Just missed emissions - little help here??
- Anyone running Dynomax or Hooker
- Equal Length shorties are driving me nuts!!
- 351 blocks
- I'm building a 347
- Re-Clocking A9L
- Fuel question?
- Short belt for a '95 GT?
- 5.0 overheats randomly.....why?
- cam question
- long tubes hits steering
- O-ring heads
- A/C removal ?
- lets talk about indexing the cam
- How to pull motor out of 94 cobra?
- Fuel Reg.help
- 68 4v heads
- Why all the Foam?????
- block / trans plate
- Gear Drive???
- I need some advice here.
- What size pipes?
- Rotating assemblies
- 70 351 windsor head questions
- Engine builders
- random overheating
- Dyno pulls
- Want to go 12's NA, need suggestions.
- Best way the strengthen a stock 302???
- Explorer SHORTBLOCK????
- Clevelor??
- Performance heads
- GT40P heads on 347
- cam numbers
- Total timing
- Cleveland head question
- Having a heck of a time with crank pulley
- Factory headers?
- Stock lower end strength??
- Manifolds?
- Right Combo Tech Advice
- Injector flow testing
- Custom Cam
- Scat or Eagle?
- what cylinder heads?
- Is this a good set-up
- 351 into fox
- 4 to 8 swap
- Reverse cooling
- want to build a motor
- Valve seal question
- Stock S/B Combo questions
- which cam
- intake couplers
- Stock block potentional
- Engine expertise requested
- Done a mass air conversion? Come on in!
- intake help
- Few Engine Q's
- trick flow track heat heads
- What Cam?